- How do you raise the height of a toilet?
- Can a shower and toilet share the same drain?
- Does a vent stack have to go straight up?
- Can an elongated toilet replace a round toilet?
- Which type of toilet is best?
- How much does a plumber charge to change out a toilet?
- Are all toilet outlets the same size?
- How do you fit a toilet pan to the floor?
- How high should soil pipe be?
- Why are toilets so low?
- How do you know if a toilet will fit?
- Can I just silicone a toilet to the floor?
- What is the standard height of a toilet waste pipe?
- What is the highest height for a toilet?
- What happens if toilet is not vented?
- Do you install a toilet on top of tile?
- What is the height of a comfort height toilet?
- Do I need to vent soil pipe?
How do you raise the height of a toilet?
Answer: You can use a toilet riser to raise the height of the toilet.
Typically by installing a riser, you can raise the height of the toilet up to 4”.
A toilet riser is bolted permanently to the floor to create a solid and sturdy base for the toilet..
Can a shower and toilet share the same drain?
Here’s the longer answer: Your shower and toilet most likely share a drain line and a vent stack (this setup is called wet venting, more on that later). If either the line or the stack has a clog or blockage, air is forced either up or down your toilet, making the gurgling noise you’re hearing.
Does a vent stack have to go straight up?
Tips for Installing Vent Pipes Vent pipes must be installed so they stay dry. This means that they should emerge from the top of the drainpipe, either straight vertically or at no less than a 45-degree angle from horizontal, so that water cannot back up into them.
Can an elongated toilet replace a round toilet?
An elongated toilet seat will technically fit on a round toilet, but the fit and comfort may be compromised. An elongated toilet seat will likely overhang a round toilet which may be fine unless the rim of the toilet is visible within the opening of the toilet seat.
Which type of toilet is best?
The 8 Best Toilets for Your Home in 2020Best Overall: TOTO MS604114CEFG#01 UltraMax II at Amazon. … Best Dual Flush: Glacier Bay Elongated All-in-One Toilet at Amazon. … Best High-End: Kohler K-4007-0 San Souci Toilet at Amazon. … Best Composting Toilet: … Best Noiseless: … Best Smart Toilet: … Best Bidet-Toilet Combo: … Best Black Toilet:
How much does a plumber charge to change out a toilet?
A relatively easy installation might cost between $150 and $250 for replacing your toilet, but on average, toilet replacement costs between $300 and $400. If you are installing a more complex unit, such as a hidden cistern or wall hung toilet, then expect to pay considerably more for your plumbers time.
Are all toilet outlets the same size?
Measurements and Drain Outlets: Rough-in dimensions are important for choosing the correct toilet for your space. Most standard floor-mount toilets have a “rough-in” dimension of 10, 12 or 14 inches. … Wall outlets can be either 4 inches off the floor, or the fixture is “hung” on the wall over the outlet.
How do you fit a toilet pan to the floor?
Once the toilet is connected to the soil pipe it’s time to secure it to the floor by screwing in the bolts. Screw each bolt in half way to begin with and then carefully tighten each one up. It’s important not to over-tighten these bolts as it can crack the toilet pan so be gentle here.
How high should soil pipe be?
900mmRegulations state that vent pipes that are situated within 3m of an opening window must terminate at least 900mm above the eaves. On a two-storey building that generally means that the open end of the pipe will be above the level of the eaves.
Why are toilets so low?
It is claimed by some that this low height forces users into a position which enables better bowl function / flow and that in fact raising the feet off the ground further increases that function. There have been several toilets / seats (higher at he front) and patents for accessories which achieve this.
How do you know if a toilet will fit?
If the base of the new toilet is shorter than the distance between the rear bolt holes and the wall, it should fit. In small bathrooms where space is tight, also measure from the sides of the flange bolts to the sidewalls or other objects to assure side-to-side clearance.
Can I just silicone a toilet to the floor?
Today the method most commonly used by plumbers to fix a toilet pan to the floor is with clear sanitary grade silicone. … The purpose of the soap and water solution is to avoid the excess silicone sticking to the floor and also your fingers as you carefully remove the excess silicone.
What is the standard height of a toilet waste pipe?
7″Slightly lower about six inch to six & half WC standard is 7″.
What is the highest height for a toilet?
17 to 19 inchesToday’s so-called “comfort height” or “right height” toilets feature bowls that are 17 to 19 inches high, as compared to the standard 15 inches of a regular toilet. The higher bowl height can be good for the knees and back and can offer real advantages to taller folks, the elderly and people with mobility problems.
What happens if toilet is not vented?
If there is not enough air pressure from the vent in the drain pipes, this water can be lost. … If there is not enough pressure in the drain lines, water in the toilet bowl or tank can flow away, resulting in inconsistent water levels.
Do you install a toilet on top of tile?
The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too. The spacing of the toilet exit “horn” and sealing surface is designed for this height.
What is the height of a comfort height toilet?
Seat Heights Toilet height is measured from the floor to the top of the seat. Heights vary enough to be noticeable. Most often, they fall somewhere between 15” and 19”, with standard toilets coming in under 17”. However, chair height toilets, what Kohler refers to as Comfort Height® toilets, measure 17” or more.
Do I need to vent soil pipe?
A soil vent pipe is installed to take waste water from upper floor toilets, baths and sinks into the underground drainage system. … This is important, because when a toilet is flushed or a sink is emptied, if the soil pipe is not vented, a partial vacuum would build up behind the waste water as it travels down the pipe.